Видео

i have an extention 900x900 for s10, and the s10 module .. if i replace it with 22w module i have to change only the attachment plate or there is something else to change ?? thank u ;)

Many of the components look like the ones used in Lynxmotion Hquad 500.

When you double your speed and add an extra pass, you will get cleaner cuts/edges.

You could have prevented the broken connector by fixing the wire better. It shouldn’t move at all during lasering.

Good Video, thanks . Iv an s10 , what way did you wire in your old air assist to work with lightburn ? Iv a large compressor so would just be looking to trigger a solenoid valve to open and close .

Thank you, excellent effort

What benefits would 2 ssd bring as opposed to 1 ssd and 1 hdd ? As the startup would run off the ssd and the hd for the extra disk space.

Post more please

This is a permanent preservation version

It is a bullshit design !!

So how long before having to redo the corrosionx spray? I mean I am watching this in 2020.

Could someone help me? I made the instalation, everything is fine. I just need to know how to effective clean the original HDD to use it as storage, and I can't find the solution.

What the leveler do you use on the phone?

Today in 2020 which machine would you recommend, I am a rc pilot been flying planes for many years.. I wish to build a machine purely for making videos & long duration quad machine.

Thanks for the videos but why the music ? :)

@MultiCopterBuil hello and welldon, do you have the tuned gain for that?

I have a 218 pro jumper and a devof12e radio but I can't make it communicate. Can you help me?

Love your video, what fpv set up did you use the link the the description isn’t working. Thanks

Super cool, i got to get me one this winter

Hi I know you make this build long time ago but can you tell me one thing....many people said that the gps module in tricopter is still hard to configure in inav ...true?

Great video!

Thank you.. that video was useful to me.. much appreciated

The individual cf parts ware well made on this frame, but the landig gear sucks. Also, the screw holes on the plastic pylon ends break EASY. They shoulda used beefier ends. Also, there is almost, but not quite enough roon to put any type of controller in the main center body. Plus the standoffs for the "battery compartment" are too short to fit any type of usefull battery, controller in there. If this kit were to come with taller standoffs and two auxillary plates, that would be dandy.

I got it your min check value is higher take it to 1070 so motor will spin earlier as normal

My gps is showing bad campass healt Its means the compass is not working Should I change the gps or is their any solution

I have the same tarot Ironman and are looking for gimbal and camera to go with it. Can you recommend and possibly do a video on how to assembly it.

I think 3SER means 3series and not 3serial.

Nice. Symbly good

A gimbal would be cool but nice build.

Followed this to the letter, including the same caddy, and the back won’t close. The caddy is about 1mm thicker than the optical drive. Any suggestions?

Hey, do you still have the drone? I would Really appreciate some pictures of the small parts, especially the rotating leg holder if possible with measurements, thank you!

Hey, did you make ALIEN 560 drone assembly video? Thought I recognised your voice from a few years back.😁

Hello could you PLEASE give me every single part's measurements and upclose view? I am really desperate at this point, i have to model this for my project that means a big deal in the future of my education,i would appreciate it Very very much!!

after all this time how do you feel about this frame and build?

After a few years, how is this build? I'm looking for something good to try building. your's is the best build video I have seen

made this and the 2 hdd dont show

The top left and bottom left screws holding in the optical drive (which describe at 3:30 and 3:32) are incredibly tight, maybe seized. Do you have any recommendations for how loosen them without stripping the screw heads?

You'll want some vibration damping under the Pixhawk!

this music xD is a FPV Reciver needet?

How long did this battery charger last before you have to replace it?

Please, Can you send me full parameter list?

THX for this vid. Btw: nice flat

Do you live in Denmark ?

Fun car. With RHD on European roads...more fun !! .

How would you compare this to the Tarot 650 Ironman?

What for a fpv transmitter do you use ? Do you use antenna Tracking?

Can this be done on a 13" late 2012 mac with retina?

no vid flying the Z-84?

Are you using the 15x5.5 carbon fiber props? Are they ok for your motors? Or you suggest others props? Thank you.

Hi .I try exact like you do,to flash,but not work for me! The motor make only one sound and not spin..What can be the problem? Thanks